Why some LED panel light is not bright in hospital indoor lighting?

Because the hospital interior lighting using LED panel lights have many advantages, and is becoming more and more extensively used, but presents the phenomenon which is not bright in use, what reason is this? Below TEK  lighting  analyse the reason why LED panel light isn't working with you.

1、The packing of the LED panel light is imperfect, so that in the process of transportation cause damage.

2、 The welding point of lamps and lanterns is virtual welding phenomenon, during transport may be shaken and led to the welding point  appear fall off and cause it to further deteriorate

3、Due to LED panel light soldering Less, solder joints prone to falls off phenomenon.

4、LED panel light lamp with soldering quality is bad, prone to brittle fracture, fall off phenomenon, may also excessive bending Angle during installation, and lead to solder joint and separation of copper foil and cause is not bright.

5、In the hospital interior lighting environment is not distorted when installation, or it will lead to solder joint fall off and cause is not bright.


Each type lamps and lanterns is in use will generate heat, LED panel light in use will produce a certain quantity of heat, especially in the summer, when we were near the lamps and lanterns can clearly feel its heat.You may not know is the service life of the LED panel light in the hospital interior lighting large degree is determined by its level of heat dissipation.


Back is one of the LED panel light emitters, its light source can be very evenly distributed in the back of the diffuser, for users to create a comfortable environment. However, back light LED panel light is can't be too thin. Why?

1, Due to the LED panel light lamp bead is fixed on the rear panel, if rear panel using the whole piece of aluminum plate, then it will greatly increase its cost.If you are using a bar of aluminum plate, so it is difficult to fixed and positioning.


2, In order to ensure the effect, should guarantee between LED light source and diffuser plate has certain spacing ，or it will see light point from the vision, so can increase the thickness of the lamps and lanterns, thus increasing the cost of the shell of lamps and lanterns.

Comments

Post a Comment

Popular posts from this blog

The advantage of new style TEK LED panel light is obvious

Image
TEK  LED panel light , continue to use the reflective surface luminous technology, light after secondary reflection through high light transmittance mask projection, reduce glare, the light is more soft and comfortable to the human eye to watch not easy fatigue, particularly for students who have long time exposure to indoor lighting lighting, subway passengers or office staff. The application of the patented reflective material ensures the reflection efficiency of the light, and the original high light effect of the panel light is retained to the maximum extent. In order to guarantee the reliability of the use,   the design principle of TEK LED panel light  adhering to the "maintenance", improve heat dissipation performance, reduce the LED light failure of lights and lanterns, significantly prolong the service life of the lights and lanterns, saving the maintenance cost of lights and lanterns. TEK LED panel light is more intelligent TEK LED panel light can form a
Read more

What ways can see LED street lights to replace the high pressure sodium lamp?

Image
Under the condition of current technology,luminous efficiency of  LED street lamp  is more than high pressure sodium lamp, it is an indisputable fact that TEK LED street lamp can reach 160 LM/W. And HPS spectrum is concentrated in the yellow area, its color temperature is low, only 2000-2500 k, and relatively high color temperature such as LED, LED street light natural white temperature of 4000-5000 k, cold white is 5000-6500 k. At the same time compared with HPS, LED street lamp with high color rendering index, close to natural light in the actual lighting, can bring a person the sense of comfort. Followed by "irradiation uniformity", although the  LED street lamp  lighting is relatively concentrated, but can be by the light path of the second design, can make the light source of lamps and lanterns presents the ideal state, realize the reasonable light distribution curve adjustment, control the distribution of light, so as to realize the uniformity of illumination.
Read more

Rule of thumb: what are the installation instructions of DALI LED high bay light?

Image
DALI LED high bay light , also known as LED warehouse light, mainly used in factory workshop, warehouse, exhibition hall, etc., have gradually entered homes, because it is using the latest LED lighting energy saving technology, high reflectivity, high power, high utilization rate of light source. But good lamps and lanterns need specification installation, to highlight its advantages, below for everyone to explain the DALI LED high bay light installation: 1，Define DALI LED high bay light installation height according to the lighting environment, because the environment will change the reflection efficiency of lamps and lanterns. Usually the height of DALI LED high bay light  should be above 5 meters, thread is not close to the lamp shell. If installation height is less than 3 meters, protective measures must be taken to prevent a vehicle to touch. 2，TEK DALI LED high bay light protection class is IP65, choose waterproof transformer, chip packaging place with high temperature resi
Read more