TEK lighting introduces you to LED street light distribution requirements

LED street light distribution could be projected onto various areas of the road as much as possible, be in different regions, according to the road to get to meet the requirements of road lighting. Light distribution of LED street lamp light distribution design is accurate in place is whether it can replace traditional street lamps one of the key factors.

The following is a description of LED street lighting distribution requirements by TEK lighting.
1,Characteristics of light distribution
In the road lighting, if the light source of LED street lamp is not distribution, the light on the road surface is a large circular spot, and Some light falls out of the road and is not used.
Schematic diagram of LED street light distribution

In order to meet on the brightness, illumination, evenness, and make the most of the light distribution on the road as far as possible to improve the utilization rate of light and reduce unnecessary waste, usually, LED street light needs to be distribution, and the light produced by the LED street lamp shines on the road, and the light pattern or spot formed  rectangle is better.

2,Standard lighting requirements for road lighting
According to the requirements of "urban road lighting design standards", road lighting road is divided into fast and main roads, sub-trunk roads and secondary roads, and LED road lighting and lighting requirements should meet the requirements.
QQ图片20170814174314.png
3,Light distribution of LED street lamps
The spatial distribution of luminous intensity is often called the distribution curve.
At the bottom of the street lamp, the light intensity should be the minimum, and as the elevation Angle theta increases, the light intensity I increases.The function relation is: the expression of the matching optical curve.The ideal lighting curve of single luminaire for road lighting.
20170116014402


Because of the complexity of optical design, it is difficult to fully conform to the function relation with the optical design, so that the projection range of theta Angle can be reduced, and the spacing of lamps and lanterns can be reduced to achieve uniform illumination.

In general, it is hoped that the "batwing" of the "bat wings" will be able to achieve a wide Angle after the lighting.

Comments

Post a Comment

Popular posts from this blog

The advantage of new style TEK LED panel light is obvious

Image
TEK  LED panel light , continue to use the reflective surface luminous technology, light after secondary reflection through high light transmittance mask projection, reduce glare, the light is more soft and comfortable to the human eye to watch not easy fatigue, particularly for students who have long time exposure to indoor lighting lighting, subway passengers or office staff. The application of the patented reflective material ensures the reflection efficiency of the light, and the original high light effect of the panel light is retained to the maximum extent. In order to guarantee the reliability of the use,   the design principle of TEK LED panel light  adhering to the "maintenance", improve heat dissipation performance, reduce the LED light failure of lights and lanterns, significantly prolong the service life of the lights and lanterns, saving the maintenance cost of lights and lanterns. TEK LED panel light is more intelligent TEK LED panel light can form a
Read more

What ways can see LED street lights to replace the high pressure sodium lamp?

Image
Under the condition of current technology,luminous efficiency of  LED street lamp  is more than high pressure sodium lamp, it is an indisputable fact that TEK LED street lamp can reach 160 LM/W. And HPS spectrum is concentrated in the yellow area, its color temperature is low, only 2000-2500 k, and relatively high color temperature such as LED, LED street light natural white temperature of 4000-5000 k, cold white is 5000-6500 k. At the same time compared with HPS, LED street lamp with high color rendering index, close to natural light in the actual lighting, can bring a person the sense of comfort. Followed by "irradiation uniformity", although the  LED street lamp  lighting is relatively concentrated, but can be by the light path of the second design, can make the light source of lamps and lanterns presents the ideal state, realize the reasonable light distribution curve adjustment, control the distribution of light, so as to realize the uniformity of illumination.
Read more

Rule of thumb: what are the installation instructions of DALI LED high bay light?

Image
DALI LED high bay light , also known as LED warehouse light, mainly used in factory workshop, warehouse, exhibition hall, etc., have gradually entered homes, because it is using the latest LED lighting energy saving technology, high reflectivity, high power, high utilization rate of light source. But good lamps and lanterns need specification installation, to highlight its advantages, below for everyone to explain the DALI LED high bay light installation: 1，Define DALI LED high bay light installation height according to the lighting environment, because the environment will change the reflection efficiency of lamps and lanterns. Usually the height of DALI LED high bay light  should be above 5 meters, thread is not close to the lamp shell. If installation height is less than 3 meters, protective measures must be taken to prevent a vehicle to touch. 2，TEK DALI LED high bay light protection class is IP65, choose waterproof transformer, chip packaging place with high temperature resi
Read more