The problems and development trend of LED street light in China

At present, China's lighting consumption accounts for about 13% of the total electricity consumption, among which road lighting accounts for 25%~30% of the total power consumption. Thus, road lighting has great energy saving potential and space.

In recent years, the development of LED street light and demonstration projects have achieved great achievements in our country, and they are among the leading countries in the world. But there are also some unsatisfactory places, and exposed some problems to be improved.
Street LED

The quality of white LED light source is not strict and the use is improper
Including the flux, light failure, light quality, thermal management, the reliability and consistency of mass products are not strict, and the domestic high power LED light blue chip failure is serious, thus causing the result of some LED street lighting engineering is bad.

High cost.
High power HBLED light source, and so on current market price is more expensive. In recent years, however, the quality of the power HB LED light source module will continuously improve and the price will decrease. The InGaN LED chip with higher efficiency and fewer defects has been successfully developed.

Advanced portable heat dissipation system, optical system and efficient power supply are required. 
At present, the high efficiency silicon thermoelectric conversion technology is used to convert the heat energy generated by the LED into electric energy using nano-silicon wires, which is expected to be realized in the future.

LED street light is the direction of street lamp development, it will undoubtedly bring considerable lighting power saving effect. In the future, the combination of solar and wind LED street light is attracting more and more attention and becomes an important development direction. 

LED street lighting is a new industry, and some related high-tech development will be beneficial to the improvement of LED street lamp to reduce the cost, industrialization and widespread use at an early date. The promotion of energy-saving LED road lighting will effectively reduce the cost of electricity, reduce the cost of cable laying and maintenance, and achieve the goal of energy conservation and emission reduction.

Comments

Post a Comment

Popular posts from this blog

The advantage of new style TEK LED panel light is obvious

Image
TEK  LED panel light , continue to use the reflective surface luminous technology, light after secondary reflection through high light transmittance mask projection, reduce glare, the light is more soft and comfortable to the human eye to watch not easy fatigue, particularly for students who have long time exposure to indoor lighting lighting, subway passengers or office staff. The application of the patented reflective material ensures the reflection efficiency of the light, and the original high light effect of the panel light is retained to the maximum extent. In order to guarantee the reliability of the use,   the design principle of TEK LED panel light  adhering to the "maintenance", improve heat dissipation performance, reduce the LED light failure of lights and lanterns, significantly prolong the service life of the lights and lanterns, saving the maintenance cost of lights and lanterns. TEK LED panel light is more intelligent TEK LED panel light can form a
Read more

What ways can see LED street lights to replace the high pressure sodium lamp?

Image
Under the condition of current technology,luminous efficiency of  LED street lamp  is more than high pressure sodium lamp, it is an indisputable fact that TEK LED street lamp can reach 160 LM/W. And HPS spectrum is concentrated in the yellow area, its color temperature is low, only 2000-2500 k, and relatively high color temperature such as LED, LED street light natural white temperature of 4000-5000 k, cold white is 5000-6500 k. At the same time compared with HPS, LED street lamp with high color rendering index, close to natural light in the actual lighting, can bring a person the sense of comfort. Followed by "irradiation uniformity", although the  LED street lamp  lighting is relatively concentrated, but can be by the light path of the second design, can make the light source of lamps and lanterns presents the ideal state, realize the reasonable light distribution curve adjustment, control the distribution of light, so as to realize the uniformity of illumination.
Read more

Rule of thumb: what are the installation instructions of DALI LED high bay light?

Image
DALI LED high bay light , also known as LED warehouse light, mainly used in factory workshop, warehouse, exhibition hall, etc., have gradually entered homes, because it is using the latest LED lighting energy saving technology, high reflectivity, high power, high utilization rate of light source. But good lamps and lanterns need specification installation, to highlight its advantages, below for everyone to explain the DALI LED high bay light installation: 1，Define DALI LED high bay light installation height according to the lighting environment, because the environment will change the reflection efficiency of lamps and lanterns. Usually the height of DALI LED high bay light  should be above 5 meters, thread is not close to the lamp shell. If installation height is less than 3 meters, protective measures must be taken to prevent a vehicle to touch. 2，TEK DALI LED high bay light protection class is IP65, choose waterproof transformer, chip packaging place with high temperature resi
Read more