How to install LED flood light in square ?
TEK LED flood light is used in many places. If the LED flood light is installed on the residential road, the average height is about 15 to 30 meters, so the distance is about 25 to 35 meters. If it is a decorative low wattage LED flood light, it is determined according to the design.
In the square, the 180W LED flood light is not too much, the illumination area is wide, the height is more than 12 meters, the radiation radius is 20-30 meters, but this is the general rule of LED flood light, not the norm.
TEK lighting also reminds that there are a lot of design factors in the installation of LED flood light, which are different from municipal lighting. For example, try to avoid the window of the occupant window to be too close to LED flood light, want to consider whether environmental protection and so on, a lot of empirical question, should be according to the actual situation setting of LED flood light installation.
How to install LED flood light ?
The main wire rope is connected by a wire rope splitter and the wire rope of the lamp plate, which can avoid the entanglement of the auxiliary steel wire due to the stretching of the main wire. The main and auxiliary steel wire rope are all used with high strength corrosion resistance 6*19 type non-rotating galvanized steel wire rope.
The lifting and lifting pulley group adopts the A3 steel bracket, stainless steel shaft and copper pulley which is treated with hot galvanizing, ensuring that it is flexible in normal atmospheric conditions. All kinds of fastener gaskets, card rings and other parts also use hot - plated zinc or non - embroidered steel.
The lifting LED flood light is equipped with both manual and electric lifting control, so that the lamp can be safely and reliably 2.5 meters from the ground to facilitate maintenance. The length of the manual remote control device is 10 meters, and the operator can control the lifting of the lamp plate at 5 meters, so as to ensure the safety of the operator.
In the rectangular inner cavity of the lower LED flood light, the electric motor and other lifting systems are installed in addition to the installation of electrical control system. Protection level of LED flood light reaches IP67, which can avoid power supply appear malfunctioning due to the bad outdoor environment.
LED flood light is also equipped with a spare cable, when light plate fell to the lowest position, the cable end inserted into the electric control system of the socket, on the other end inserted into the lamp terminal box, therefore, the lamp can be supply electricity directly and can be checked and repaired
In the square, the 180W LED flood light is not too much, the illumination area is wide, the height is more than 12 meters, the radiation radius is 20-30 meters, but this is the general rule of LED flood light, not the norm.
TEK lighting also reminds that there are a lot of design factors in the installation of LED flood light, which are different from municipal lighting. For example, try to avoid the window of the occupant window to be too close to LED flood light, want to consider whether environmental protection and so on, a lot of empirical question, should be according to the actual situation setting of LED flood light installation.
How to install LED flood light ?
The main wire rope is connected by a wire rope splitter and the wire rope of the lamp plate, which can avoid the entanglement of the auxiliary steel wire due to the stretching of the main wire. The main and auxiliary steel wire rope are all used with high strength corrosion resistance 6*19 type non-rotating galvanized steel wire rope.
The lifting and lifting pulley group adopts the A3 steel bracket, stainless steel shaft and copper pulley which is treated with hot galvanizing, ensuring that it is flexible in normal atmospheric conditions. All kinds of fastener gaskets, card rings and other parts also use hot - plated zinc or non - embroidered steel.
The lifting LED flood light is equipped with both manual and electric lifting control, so that the lamp can be safely and reliably 2.5 meters from the ground to facilitate maintenance. The length of the manual remote control device is 10 meters, and the operator can control the lifting of the lamp plate at 5 meters, so as to ensure the safety of the operator.
In the rectangular inner cavity of the lower LED flood light, the electric motor and other lifting systems are installed in addition to the installation of electrical control system. Protection level of LED flood light reaches IP67, which can avoid power supply appear malfunctioning due to the bad outdoor environment.
LED flood light is also equipped with a spare cable, when light plate fell to the lowest position, the cable end inserted into the electric control system of the socket, on the other end inserted into the lamp terminal box, therefore, the lamp can be supply electricity directly and can be checked and repaired
Comments
Post a Comment