What are the factors that need to considered when LED street light changes the design and installation of parking lot?

When it comes to parking after dark, most people don't pay attention to the quality of the light unless the lamp is broken. Light enough space can make drivers and pedestrians feel safe, driving or walking is easier. On the other hand, the lack of space for lighting not only increases the probability of accidents, but also increases crime. Therefore, TEK recommends you use LED street light.

Lighting engineers know that proper lighting in public spaces is critical. The parking lot deserves special consideration, and the following three aspects should be studied in the planning and implementation process.
-1 (2)
  1. Structural considerations
The first thing to think about is the light pole of LED street light.When researching options, it's not just looking for durable materials. TEK LED street lights can be designed to support single or multiple lamps, usually the best choice for parking lots.

Many streets and car parks in USA, HID lamps are outdated and gradually being phased out and replaced by modern LED street light. HID lamp does not save energy, also can produce bright spot and black dot, reduce visibility, increase crime rate indirectly. LED street light have high efficiency, long duration and can produce accurate controlled light output. This means reduce waste light, more visibility, and more uniform outdoor space after dark.

  1. Lighting use and design
Spatial use is another important consideration when choosing the right lighting solution. Whether in the new area, or in the case of renovation, lamps and lanterns must provide uniform non-glare lighting. But that doesn't mean to light up the space as much as possible. Misuse of artificial light causes light pollution, a growing problem worldwide.

So it is necessary to choose appropriate wattage, TEK LED street light provide 60w - 210w, can let the customer choose according to their own actual situation, the appropriate brightness can not only meet the needs of lighting can also make the physical and mental health.

  1. Installation concerns
Once you have fixed the correct wattage LED street light, you will be ready to install it. Most of the lights in the parking lot are mounted on reinforced concrete bases and supported by steel bars. Work with qualified engineers who understand load conditions.
000-MavThVOCZQon
Before pouring concrete, make sure the anchor bolt circle template fits the bolt circle at the bottom of the rod. Remember the anchor bolt projection (BP) - the height of the anchor bolt above the concrete surface - to eliminate unnecessary bending and stress.

Comments

Post a Comment

Popular posts from this blog

The advantage of new style TEK LED panel light is obvious

Image
TEK  LED panel light , continue to use the reflective surface luminous technology, light after secondary reflection through high light transmittance mask projection, reduce glare, the light is more soft and comfortable to the human eye to watch not easy fatigue, particularly for students who have long time exposure to indoor lighting lighting, subway passengers or office staff. The application of the patented reflective material ensures the reflection efficiency of the light, and the original high light effect of the panel light is retained to the maximum extent. In order to guarantee the reliability of the use,   the design principle of TEK LED panel light  adhering to the "maintenance", improve heat dissipation performance, reduce the LED light failure of lights and lanterns, significantly prolong the service life of the lights and lanterns, saving the maintenance cost of lights and lanterns. TEK LED panel light is more intelligent TEK LED panel light can form a
Read more

What ways can see LED street lights to replace the high pressure sodium lamp?

Image
Under the condition of current technology,luminous efficiency of  LED street lamp  is more than high pressure sodium lamp, it is an indisputable fact that TEK LED street lamp can reach 160 LM/W. And HPS spectrum is concentrated in the yellow area, its color temperature is low, only 2000-2500 k, and relatively high color temperature such as LED, LED street light natural white temperature of 4000-5000 k, cold white is 5000-6500 k. At the same time compared with HPS, LED street lamp with high color rendering index, close to natural light in the actual lighting, can bring a person the sense of comfort. Followed by "irradiation uniformity", although the  LED street lamp  lighting is relatively concentrated, but can be by the light path of the second design, can make the light source of lamps and lanterns presents the ideal state, realize the reasonable light distribution curve adjustment, control the distribution of light, so as to realize the uniformity of illumination.
Read more

Rule of thumb: what are the installation instructions of DALI LED high bay light?

Image
DALI LED high bay light , also known as LED warehouse light, mainly used in factory workshop, warehouse, exhibition hall, etc., have gradually entered homes, because it is using the latest LED lighting energy saving technology, high reflectivity, high power, high utilization rate of light source. But good lamps and lanterns need specification installation, to highlight its advantages, below for everyone to explain the DALI LED high bay light installation: 1，Define DALI LED high bay light installation height according to the lighting environment, because the environment will change the reflection efficiency of lamps and lanterns. Usually the height of DALI LED high bay light  should be above 5 meters, thread is not close to the lamp shell. If installation height is less than 3 meters, protective measures must be taken to prevent a vehicle to touch. 2，TEK DALI LED high bay light protection class is IP65, choose waterproof transformer, chip packaging place with high temperature resi
Read more